ghost vehicle immobiliser is the UK's most advanced aftermarket immobiliser for the CAN bus. It is discreet and does not have LED indicators or key fobs, and is concealed in the wiring of your vehicle.
The user can also disable the system temporarily by using Transport Mode when renting their vehicle. This guide will guide you through the process of installing the Ghost immobiliser.
Professional Installation
The Autowatch Ghost immobiliser is a advanced security device that safeguards your vehicle from key cloning, hacking and relay attacks. The system is directly connected to the ECU of your vehicle and protected by a pin code that you choose. It's inaccessible to thieves using scanners for diagnostics or other modern methods, and is unable to be disabled by cutting circuits.
The system is simple to use, but it's important to have professional installation to ensure a smooth and secure connection with your vehicle's ECU. A Thatcham-approved installer can help with the installation and programming of your Ghost system. ghost immobilisers can also recommend an alarm or tracking system to complete the protection package for your vehicle.
To prevent an accidental deployment of short circuits or airbags To avoid an accidental deployment of airbags or short circuits, the installer must disconnect your battery. After that the installer is able to safely begin work. Hand tools are essential for securing connections with precision and a multimeter can be used to verify electrical values and ensure safety. Cable ties and insulation tape are also essential for protecting connections and keeping wiring neat. In addition, the user's manual gives specific guidelines that are specifically tailored to the Ghost Immobiliser model you have.
It is crucial to select an area for grounding that is free of dirt or paint during installation. Installers should also ensure that the immobiliser's wires, CAN H and CAN L are connected to the proper ECU ports. Depending on the model, these wires may need to be soldered or plugged into. Using a quality connector is recommended to ensure a durable and secure connection.
Once the install is complete Once the installation is completed, the customer can enable after the installation is complete, the customer can activate Transport Mode. This allows mechanics or valet parking to use the vehicle without knowing the pin code. The customer must press the service icon on the dashboard five times in two seconds. After that the system will verify with 5 signal indicators.
The Autowatch Ghost 2 immobiliser is TASSA approved and is a highly efficient immobiliser. It's an excellent choice for those who rent their vehicles regularly on platforms such as Turo. Immobilisers can also lower insurance costs since it greatly reduces the chance of theft.
Getting Started
If you are looking for a solution that will secure your vehicle from thieves You can't go wrong with an autowatch ghost immobiliser. It will stop your car from starting even the theft or copies the key. It is possible because of its advanced technology that prevents the engine from starting until the right PIN code has been entered.
The device connects to the vehicle's bus network, CAN and allows direct communication with the ECU. It uses buttons that are already present on the dashboard and the steering wheel to create a unique sequence that only you can identify which makes it impossible for anyone else to start your vehicle. This is the best way to protect your pride and joy. It will not lose its value should you ever decide to sell it.
Installing a ghost ignition is a simple process, but it's important to follow the directions carefully to avoid problems with the electrical system and malfunctions. First, you must find a 12V power source and a good grounding on the chassis of your car. Then, you can begin connecting the wires to the immobiliser. Use high-quality connectors and soldering methods to create an effective connection. Make sure to shield the connections with heat shrink tubing, insulation tape or other materials to avoid short circuits in electrical power.
After the wires are connected, you can connect the battery and start the engine to determine whether the immobiliser works. Once you have verified that everything is working properly and you are satisfied, you can place the immobiliser in a secure position inside the vehicle. Make sure to cover it well so that a thief cannot tamper with it.
The Ghost 2 immobiliser is TASSA (Tracker and Aftermarket Security System Association) verified this means it complies with the highest standards of security and is a fantastic protection against car thieves. It offers superior protection against key cloning, hacking and relay attacks, and it cannot be disabled without knowing the code. The device is also simple to use and can be put into an auto valet mode so that your car will not be activated when you bring it in for maintenance or an MOT.
Wiring
The Ghost Immobiliser, a cutting edge security system, is designed to stop theft of vehicles. It connects directly to your car's CAN bus network and communicates with the ECU, making it virtually undetectable to your vehicle. Unlike other aftermarket systems that require the removal of circuit components, the Ghost Immobiliser doesn't interfere with the factory settings for your vehicle.
It's also completely undetectable to thieves using diagnostic scanners. The system does not send or receive radio frequency signals, but instead uses CAN data for communication with your ECU. In addition, it doesn't need any modification to your vehicle's existing key fobs.
Enter the sequence to disarm (either two or one button) and then switch on the ignition of your car to activate Ghost Immobiliser. The indicator will flash twice to verify that you've entered the correct code. Once you've verified this, you're able to start your car and drive away with peace of mind.
Once installed, the Ghost Immobiliser safeguards your vehicle against hacking or key cloning while preserving its value. In Transport Mode you can temporarily disable the Ghost Immobiliser in case you need to give your car to service or valet park.
You'll require a continuous power source (12V) in addition to an earthing point to complete the installation of a Ghost immobiliser. Make sure that both are properly insulated and can be touched. Cable ties are also recommended to secure the wires. This reduces the risk of theft by potential thieves. To avoid making mistakes, make sure to double-check these points and mark them with labels or tape. It's recommended to check all connections for signs of wear and tear. Connectors that are loose could cause malfunctions in the system, so make sure they're securely fixed and well-insulated. Make sure to test your Ghost Immobiliser after the installation is completed. This will make sure that the unit is functioning properly and that all connections are safe and well-insulated. If there are any issues, you must be sure to address them immediately.
Testing
The Autowatch Ghost Immobiliser is a cutting-edge vehicle security system that integrates seamlessly into your car's ECU to block the engine from starting without authorization. Its innovative technology safeguards your vehicle from key cloning and hacking and other methods employed by thieves to steal cars. The Ghost is a perfect complement to existing alarm and tracking systems to provide the most effective security for your vehicle. The Ghost's unique features and subtle design make it a popular choice for car lovers and security-conscious drivers too.
It is essential to follow the procedures for installation to ensure the correct integration of the Ghost Immobiliser. The best way to begin is to consult the vehicle's wiring diagram that will serve as a guideline to locate and connecting the required wires. The next step is to identify the power source as well as grounding points. Once you've found them then you'll have to mark them in a way that they're easily identifiable during the installation process. It is also important to use top-quality tools and materials. Hand tools are essential to assist you in making precise connections. A multimeter can verify electrical values and guarantee safety. Insulation tape and cable tie will ensure that all connections are tidy. A Ghost-specific user's manual is also available.
It is essential to test the system prior installing it. Enter the PIN code into the system, and then start the vehicle. This test will verify that the immobiliser is working as it should and stop unauthorised vehicle starts. It's recommended to perform this routinely as part of your regular vehicle inspections to ensure that the system is always functioning properly.
Once the installation is complete After the installation is completed, you are able to drive your vehicle with confidence. The Ghost will keep your pride and joy safe from potential thieves, ensuring that nobody can take off with your vehicle without the proper PIN code. The Ghost can be paired with an approved Thatcham tracker, which detects attempts to steal or tamper with. This lets you track your car in the event that it's stolen.
The Ghost is compatible with a variety of vehicles, including those from all major manufacturers. If you are looking to secure your vehicle with this innovative device, contact Monty's Locksmith today to learn more about our installation and service options. We are a TASSA registered installer, a certificate that guarantees we follow strict standards for installing our products. This assures customers, insurance companies and law enforcement agencies that installations are done safely and in a correct manner.